Emerson Bristol ControlWave LP Manual de Instruções descarregar pdf (Página 147)

Section 5 - Wiring Techniques Page 5-3 S1400CW

5.2.3 Grounding of Cable Shields

DO NOT connect the cable shield to more than one ground point; it should only be grounded

at one end. Cable shields that are grounded at more than one point or at both ends may

have a tendency to induce circulating currents or sneak circuits that raise havoc with I/O

signals. This will occur when the ground systems associated with multipoint connections to

a cable shield have a high resistance or impedance between them and a ground induced

voltage is developed (for what ever reason, i.e., man made error or nature produced

phenomena).

5.2.4 Use of Known Good Earth Grounds

ControlWave units should only have one connection to earth ground. For ControlWave

and ControlWave MICRO Process Automation Controllers, ControlWave MICRO,

ControlWave EFM Electronic Flow Meters, ControlWave GFC/XFC Gas Flow Computers

and ControlWave I/O Expansion Racks, this connection is provided via the Ground Lug

that is situated on the bottom of the unit. ControlWaveLPs require the installation of a

ground lug, ground bus or ground plate/panel. Since ControlWave units are DC-based

systems, grounding does not take into account AC power grounding considerations. Earth

grounding the unit is absolutely necessary when the unit is equipped with a radio or

modem. Additionally these units should be connected to earth ground when they are

installed in areas that have frequent lightning strikes or are located near or used in

conjunction with equipment that is likely to be struck by lightning or if struck by lightning

may cause equipment or associated system failure. Earth Grounds must be tested and must

be known to be good before connecting the ControlWave. Earth grounds must be

periodically tested and maintained (see Section 4).

5.2.5 Earth Ground Wires

Earth connections must utilize smoothly dressed large wire. Use AWG 3 or 4 stranded

copper wire with as short a length as possible. Exercise care when trimming the insulation

from the wire ends. Twists the strands tightly, trim off any frizzes and tin the ends with

solder. The earth ground wire should be clamped or brazed to the Ground Bed Conductor

(that is typically a standard AWG 0000 copper cable. The earth ground wire should be run

such that any routing bend in the cable is a minimum 8-inch radius above ground or a

minimum 12-inch radius below ground.

5.2.6 Working Neatly & Professionally

Take pride in your work and observe all site and maintenance safety precautions. After

properly trimming the stranded pair wire ends, twist them in the same direction as their

manufacturer did and then tin them with solder. Install the tinned wire end into it’s

connector and then secure the associated connector’s clamping screw. Remember to check

these connections for tightness from time to time. If solid copper wire is used (in

conjunction with the DC Power System or for Earth Ground) make sure that the conductor

is not nicked when trimming off the insulation. Nicked conductors are potential disasters

waiting to happen. Neatly trim shields and whenever possible, coat them to protect them

and prevent shorts and water entry.

1 2 ... 142 143 144 145 146 147 148 149 150 151 152 ... 165 166

Comentários a estes Manuais

Sem comentários

Modelle	Dokumententyp
EDGE modem	Bedienungsanleitung Panasonic EDGE modem User Manual, 20 Seiten
ePassport Reader JT-P100	Bedienungsanleitung Panasonic ePassport Reader JT-P100 User Manual, 2 Seiten
ET-MD77NT	Bedienungsanleitung Panasonic ET-MD77NT User Manual, 5 Seiten
ET-RMRC2	Bedienungsanleitung Panasonic ET-RMRC2 User Manual [en] , 1 Seiten
EZADT series	Bedienungsanleitung Panasonic EZADT series User Manual, 2 Seiten

Emerson Bristol ControlWave LP Manual de Instruções Página 147

Comentários a estes Manuais

Panasonic Hardware Benutzerhandbücher

Emerson Bristol ControlWave LP Manual de Instruções Página 147

Comentários a estes Manuais

Manuais e produtos relacionados com Redes Emerson Bristol ControlWave LP

Panasonic Hardware Benutzerhandbücher