Emerson Vission Manual de Serviço descarregar pdf (Página 122)

19 – 2

Vission 20/20 • Operation and Service Manual •Vilter/Emerson • 35391SC 1.9

Time & Date

This section sets the time and date of the Vission 20/20.

Accurate time and date are accentual for accurate log-

ging and troubleshooting. Setting these parameters will

set the hardware clock embedded in the Vission 20/20

CPU. If the time is not retained after powering down the

panel, the operator should check and/or replace the coin

style battery on the panel SBC behind the touchscreen.

Format:

• Selection to choose between 12 hour or 24 hours

clock.

Hour:

• Entry box to set the clock hours. AM or PM drop-down

box will available if the 12 hour format is selected.

Minute:

• Entry Box to set the clock minutes.

Second:

• Entry Box to set the clock seconds.

Year:

• Entry Box to set the current year.

Month:

• Entry Box to set the current month.

Day:

• Entry Box to set the current date.

Communications

The communication section is the control center for all

communications to the Vission 20/20 panel. It is possi-

ble to have multiple modes of communications enabled

and used. However, only one mode can be used to con-

trol the Vission 20/20 which is selected in the “Active

Remote Control” drop-down box. For a complete list

of communication registers, please refer to the Vission

20/20 communication table.

Active Remote Control:

• Selects the mode of remote control. The operator

can select between Direct I/O, Serial, or Ethernet.

Direct I/O:

• Enables the Direct I/O inputs. Once selected a pop-up

will be displayed and the operator will need to choose

a one of the three Direct I/O options

Serial (Modbus RTU):

• Enables the Serial Modbus RTU protocol. Once se-

lected, the remainder of the serial setpoints will be

available for editing.

Panel ID:

• Panel Identiﬁ er used by the controller when commu-

nicating with multiple panels.

Port:

• The Vission 20/20 has two ways to communicate on

serial bus. Either via the built in serial port, P12, or

through one of the USB ports. This drop-down box

allows the operator to chose which one will be used.

Baud Rate:

• Sets the Baud Rate for the serial communication.

Data Bits:

• Fixed at 8 Data bits.

Stop Bits:

• Identiﬁ es the end of character for re-synchronizing.

Parity:

• Identiﬁ es the type of error detection.

Ethernet:

• Enables the Ethernet port. Once selected, the re-

mainder of the Ethernet setpoints will be available for

editing.

Panel ID:

• Panel Identiﬁ er used by the controller when commu-

nicating with multiple panels.

IP Address:

• Entry box to set the IP address.

Subnet Mask:

• Entry box to set the Subnet Mask.

Gateway:

• Entry box to set the Gateway address.

Protocol:

• Drop-down box to select the type of protocol used to

remotely control the Vission 20/20.

Touchscreen

The “Calibrate” button changes the screen into touch-

screen calibration mode. Calibrating the touchscreen

is only required if the operator ﬁ nds that the pointer ar-

row no longer follows his ﬁ nger. The calibration mode

requires the operator to touch the four corners of the

touchscreen and then the accept button.

Section 19 • Configuration

1 2 ... 117 118 119 120 121 122 123 124 125 126 127 ... 261 262

Emerson Vission Manual de Serviço Página 122

Comentários a estes Manuais

Emerson Vission Manual de Serviço Página 122

Comentários a estes Manuais

Manuais e produtos relacionados com Software Emerson Vission