Emerson LMS 1000 Manual de Instalação descarregar pdf (Página 136)

NetSure™ LMS Data Processing Unit

Installation Instructions, Section 5879 (Issue BA, April 7, 2014)

Spec. No: 58650500, 586505500 Code: Section 5879

Model No: LMS1000 Issue BA, April 7, 2014

[128 of 149]

Changing the Function Channel Configurations

The function channel configurations can be changed by using the command CONFIG. The command CONFIG is also described in

"Commands" of the User Instructions (Section 5847). Section 5847 can be accessed via the CD (Electronic Documentation Package)

furnished with your system. The command, when entered, will display a header that contains the current configuration. Then,

individually, the command will list each item that can be changed, showing the current information, and then prompting for new or

revised information to be entered. If the current information does not need to be changed, press

ENTER to continue.

Command CONFIG: If the command CONFIG is entered, the system will ask that you identify which channel you wish to modify. Another

way of entering the command is to identify the desired channel in the command line by typing the channel number after the characters

CONFIG (ex. CONFIG F1). The various information pertaining to a function channel that can be changed through this command is

described below. This command is available to users programmed for access to level 6 commands.

Note:

In a 582140000, 582140001, and 582126100 Power System, function channel 64 is dedicated for summing the total current output of

conventional rectifiers in a hybrid application. The channel name for F64 defaults to “Total Rectifier Output.” The LMS updates the MCA

with the calculated value for the configured program line.

Note:

Parameters which apply only to TL1 commands/messages do not appear for configuration if the TL1 software option is not installed.

CONFIG F_

Command <6>: CONFIG F1

Type

CONFIG F1

, then press

ENTER

Channel active (Y or N):

Note:

If "Y" is entered, the system will

allow the default configuration

information of the current function

channel to be changed as shown

below.

Type

if the channel is required to be active and

if not, then press

ENTER

If "N" was entered above, the system

responds with...

Set channel configuration to

default values? (Y or N):

Type

to change the attributes of this channel to their default values.

Note:

If ”Y” is entered, this command terminates.

If ”N” is entered, the system will allow the default configuration

information of the current function channel to be changed as shown

below.

Name:

Type the desired name for this function channel (30 characters

maximum), then press

ENTER

Sub-access Identifier:

This parameter applies only to TL1 commands/messages. Type the

name (20 characters maximum) of the sub-access identifier that this

channel belongs to, then press

ENTER

. The group of LMS1000 channels

monitoring a sub-entity in an NMA system should have the same

access identifier and sub-access identifier. Only alpha-numeric

characters can be entered for this parameter. TL1 uses specific values

for this parameter. Refer to TA-NWT-001360, Table 4-1.

System Alarm Report mode (Y or

N):

Type

if the system is required to initiate an alarm report via phone

lines if an alarm limit is exceeded on this channel and

if not, then

press

ENTER

Monitor type:

This parameter applies only to TL1 commands/messages. Type the

name of the unit (10 characters maximum) that the above alarms are

measured in (ex. VOLTDC, CURDC, etc.), then press

ENTER

. Only alpha

characters can be entered for this parameter. TL1 uses specific values

for this parameter. Refer to TA-NWT-001360 Table 6-1.

1 2 ... 131 132 133 134 135 136 137 138 139 140 141 ... 157 158

Comentários a estes Manuais

Sem comentários

Emerson LMS 1000 Manual de Instalação Página 136

Comentários a estes Manuais

Manuais e produtos relacionados com não Emerson LMS 1000