Emerson HSP2600 Manual de Instruções descarregar pdf (Página 6)

The Humidier Automatic Flushing Timer

automatically ushes accumulated min-

eral deposits from all central-system

steam- and reservoir-type humidiers.

This enables homeowners to enjoy the

benets of healthful, humidied air without

the hassles of frequent maintenance due

to mineral buildup.

The ushing timer is set at the factory

to ush the humidier every two hours

for a duration of 10 seconds, using

only about 1.5 gallons of water per day.

(See “To Reprogram the Automatic Flushing Timer”, pages 11 and 12, for

alternate settings.) This ushing reduces or eliminates servicing during the

humidication season, depending on the mineral content of the water.

How To Install the

Pro grammable Automatic Flushing Timer

To Install the Flushing Timer on a Steam Humidier:

Locate a suitable waste drain for disposal of ushed water.

CAUTION: Drain tubing must not kink or come in contact with

sharp edges or hot surfaces. Tubing must run in a continual down-

hill slope to allow proper drainage and to prevent overow.

4a. If this ushing timer was purchased as an accessory to install on a

steam humidier... remove the drain valve from the humidier and

install the 90º barbed tting (provided). (See Figure 9 on page 10.)

4b. If this ushing timer was purchased with the steam humidier as a

complete assembly... the 90º barbed tting should already be installed

on the humidier in the proper location. (See Figure 9 on page 10.)

Screw the unit to the mounting surface selected in Step #2.

Cut a piece of drain tubing to reach from the humidier tting to the tting

on the side of the ushing timer.

CAUTION: Drain tubing must not kink or come in contact with sharp

edges or hot surfaces. (This caution applies to step #7, as well.)

Cut a second piece of tubing to reach from the bottom tting on the

ushing timer to the drain. (See Step #3.)

Connect tubing with clamps or ttings suitable for your installation.

Return the steam humidier to its normal operating mode. Refer to pages

8 & 9 to properly set the water level.

Plug the ushing timer into the designated outlet. (See Step #2.)

Check all ttings for leaks. Tighten as necessary.

Test the ushing timer for proper operation.

Press and release the MANUAL button.

Wait 10 to 30 seconds* until the ushing noise stops, indicating that

the ushing cycle is complete.

*The number of seconds will vary depending upon how the unit is

programmed. (See “To Reprogram the Automatic Flushing Timer”,

below.)

To Reprogram the Automatic Flushing Timer:

The ushing timer is set at the factory to ush the humidier every two hours

for a duration of 10 seconds, using approximately 1.5 gallons of water per

day. Although the two-hour intervals between ushes may not be altered, the

duration may be lengthened to either 20 or 30 seconds per ush.

Unplug the ushing timer from the electrical outlet.

Take off the back cover plate by removing the three screws closest to

the mounting anges.

10.

11.

12.

Figure 9—Installation of a

Programmable Automatic

Flushing Timer on a Steam

Humidier

CAUTION: All plumb-

ing and electrical con-

nections must comply

with relevant codes and

ordinances.

If the humidier has

been preinstalled and

needs servicing, refer

to “How to Maintain a

White-Rodgers Com-

fortPlus Humidier”

(page 12) for instructions.

For either a new or preinstalled humidier, select a suitable mounting

locations for the ushing timer within 3 feet of the humidier, and within

10 feet of a properly fused electrical outlet.

1 2 3 4 5 6 7 8 9 10 11

Comentários a estes Manuais

Sem comentários

Emerson HSP2600 Manual de Instruções Página 6

Comentários a estes Manuais

Manuais e produtos relacionados com Desumidificadores Emerson HSP2600