Emerson 1410 Manual de Serviço Página 111
- Página / 222
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuring and Operating the System
AXP 1410 Installation and Use (6806800H70D)
111
5.7.3 Redundancy Operations
This section describes what happens during shelf manager switchover, takeover, failover, and
when a shelf manager is inserted or extracted.
5.7.3.1 Shelf Manager Switchover
During a switchover, the active and the standby shelf manager change their roles. The system
manager initiates and controls this process on the active shelf manager. A switchover is, for
example, necessary when the active shelf manager needs to be extracted. Since only the
standby shelf manager can be extracted, a switchover needs to take place.
- AXP 1410 1
- Trademarks 2
- Contact Address 2
- Contents 3
- List of Tables 10
- List of Figures 13
- About this Manual 15
- Abbreviations 16
- Conventions 19
- Summary of Changes 20
- Comments and Suggestions 21
- System Overview 23
- 1.1.1 Shelf 26
- 1.1.2 Backplane 26
- 1.1.3 Shelf Manager 26
- 1.1.4 Blades 27
- 1.1.5 Hub Slots 28
- 1.1.6 Rear Transition Modules 28
- 1.1.7 Power Entry Modules 28
- 1.1.8 Fan Tray Modules 28
- 1.2 Standard Compliances 29
- 1.3 Ordering Information 30
- 1.4 Product Identification 32
- Site Preparation 35
- 2.3 Requirements 37
- 2.3.2 Power Requirements 39
- 2.4 Dimensions and Weight 40
- 2.5 Mounting Options 41
- 2.6 Cooling Considerations 42
- 2.7 Acoustic Noise Control 44
- 3.3 Installation 46
- 3.3.2 Connecting the Cables 51
- 3.3.2.1 DC Power Cable 52
- 3.3.3 Grounding the System 56
- 3.3.4 Powering Up the System 57
- 3.4 Powering Down the System 58
- 3.5 Emergency Power Off 58
- FRU Installation 61
- 4.2.1 Installing the Board 63
- 4.2.2 Removing the Board 64
- 4.3.1 Tools You Will Need 65
- 4.3.2 Removing the PEM 65
- 4.3.3 Installing the PEM 68
- 4.4.1 Removing the Upper FTM 73
- 4.4.3 Removing the Lower FTM 74
- 4.5 Installing a Fan Filter 75
- Chapter 5 79
- 5.1 Overview 79
- 5.2 Network Management 79
- ATCA Hub 82
- Blade #1 82
- Blade #n 82
- # hpishaddr -b "07" 85
- 5.2.4 IP Addresses 86
- SAM1410-1 87
- SAM1410-2 87
- 5.2.4.1 Out-of-Band Interface 88
- 5.2.4.2 Backplane Interfaces 91
- 5.2.4.3 Configuration File 94
- 5.4 Software 100
- 5.4.2 Upgrade 101
- 5.5 Power Entry Module (PEM) 102
- 5.5.2 IPMC Circuitry 103
- 5.6 Fan Tray Modules 104
- 5.6.2 Cooling Budget 105
- 5.7 Redundancy 106
- 5.7.1.1 Heartbeat 107
- 5.7.1.2 Data Replication 107
- 5.7.1.3 HPI Interface 107
- 5.7.2.1 Shelf Manager 108
- 5.7.2.2 Hub Blade 109
- 5.7.2.3 System Manager 109
- Figure 5-5 System Start-Up 110
- 5.7.3 Redundancy Operations 111
- Supported IPMI Commands 119
- 6.2.3 Sensor Device Commands 120
- 6.2.4 FRU Device Commands 120
- 6.3 PICMG 3.0 Commands 121
- Chapter 7 123
- 7.1 Introduction 123
- 7.2.2.1 Voltage Sensors 125
- Table 7-4 Sensor No. 5 +3.3V 127
- 7.2.2.2 Temperature Sensors 129
- 7.2.2.3 Fan Speed Sensors 133
- Table 7-14 Sensor No. 9 Fan 2 134
- 7.2.3.1 Hot Swap Sensor 143
- 7.2.3.2 IPMB Link Sensor 143
- 7.2.3.3 Reserved Sensor 144
- 7.2.3.4 OEM-Reserved Sensors 145
- 7.3.1 PEM FRU Information 152
- 7.3.2 E-Keying 153
- 7.3.3 Power Configuration 154
- Voltage Sensors 155
- Current Sensors 155
- Temperature Sensor 155
- 7.3.5.1 Voltage Sensors 156
- 7.3.5.2 Current Sensors 161
- 7.3.5.3 Temperature Sensor 162
- 7.3.6.1 Hot Swap Sensor 163
- 7.3.6.2 IPMB Link Sensor 164
- Table 7-51 Sensor No. 5, CB 1 165
- Table 7-52 Sensor No. 6 CB 2 166
- Table 7-53 Sensor No. 7 CB 3 167
- Table 7-54 Sensor No. 8 CB 4 167
- Table 7-55 Sensor No. 9 CB 5 168
- Shelf Management Alarm Module 171
- 8.2 Features 172
- 8.4 Functional Description 176
- 8.4.3 Master-Only I 177
- 8.4.4 Shelf FRU SEEPROM 177
- 8.4.5 SAM LEDs 178
- 8.5 Management and Control 179
- 8.5.1.1 Voltage Sensors 180
- 8.5.1.3 Fan Speed and Control 180
- 8.5.2 Redundancy Control 183
- 8.5.2.2 HRI Protocol 184
- 8.5.2.3 Ethernet Signals 185
- 8.6 Telco Alarm Functionality 186
- 8.6.2 Telco Alarm LEDs 187
- 8.6.3 Telco Alarm Interface 187
- 8.7 Hot Swap Interface 188
- 8.8 Power 188
- 8.9 SAM Software 188
- 8.9.1 imls Utility 189
- Related Documentation 191
- A.2 Related Specifications 192
- Safety Notes 193
- Operation 195
- Grounding 197
- Connectors and Cabling 199
- Expansion and FRU Exchange 200
- Environment 203
- Sicherheitshinweise 205
- System Installation 206
- Stecker und Verkabelung 211
- Umweltschutz 215
- , 180, 188 219
- © 2009 Emerson Electric Co 222
Manuais e produtos relacionados com Gateways/controladores Emerson 1410
Gateways/controladores Emerson MRLDS Especificações
(26 páginas)
(26 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.120 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais