Emerson Rosemount 2051 Wireless Pressure Transmitters Manual do Utilizador Página 50
- Página / 154
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
38
Reference Manual
00809-0100-4102, Rev AA
Section 3: Installation
May 2013
Installation
Bolt installation
Only use bolts supplied with the Rosemount 2051 or sold by Emerson Process Management as
spare parts. When installing the transmitter to one of the optional mounting brackets, torque
the bolts to 125 in-lb. (0,9 N-m). Use the following bolt installation procedure:
1. Finger-tighten the bolts.
2. Torque the bolts to the initial torque value using a crossing pattern.
3. Torque the bolts to the final torque value using the same crossing pattern.
Torque values for the flange and manifold adapter bolts are as follows:
Table 3-2. Bolt Installation Torque Values
Figure 3-6. Traditional flange bolt configurations
A. Differential Transmitter
B. Gage/Absolute Transmitter
C. Drain/Vent
D. Vented fitting
E. 1.75 (44) × 4
F. 1.50 (38) × 4
(1)
Bolt Material Initial Torque Value Final Torque Value
CS-ASTM-A445 Standard 300 in.-lb (34 N-m) 650 in.-lb (73 N-m)
316 SST—Option L4 150 in.-lb (17 N-m) 300 in.-lb (34 N-m)
ASTM-A-193-B7M—Option L5 300 in.-lb (34 N-m) 650 in.-lb (73 N-m)
Alloy K-500—Option L6 300 in.-lb (34 N-m) 650 in.-lb (73 N-m)
ASTM-A-453-660—Option L7 150 in.-lb (17 N-m) 300 in.-lb (34 N-m)
ASTM-A-193-B8M—Option L8 150 in.-lb (17 N-m) 300 in.-lb (34 N-m)
(1) For Gage and Absolute Transmitters: 150 (38) x 2
AB
C
C
D
C
E
E
FF
Note
Dimensions are in inches
- Protocol 1
- Contents 7
- 3Section 3: Installation 8
- 4Section 4: Commissioning 9
- 6Section 6: Troubleshooting 9
- Reference Data 10
- Reference Manual 11
- Table of Contents 11
- Section 1 Introduction 13
- 1.4 Transmitter overview 16
- 1.5.1 Wireless considerations 17
- 1.5.2 Mechanical 18
- 1.5.3 Electrical 18
- 1.6 Service support 19
- Section 2 Configuration 21
- Warnings ( ) 22
- 2.4 Basic setup 23
- 2.4.2 Join device to network 24
- 2.4.3 Configure update rate 24
- 2.5 Configure for Pressure 25
- 2.5.2 Set range points 26
- 2, 2, 4, 2 27
- DP Level Example 29
- DP Flow example 29
- 2.6.3 Set range points 31
- 2.7 Review configuration data 32
- Fast Keys 33
- 2.9.2 Damping 35
- 2.10 Diagnostics and service 36
- 2.10.1 Device reset 37
- 2.10.2 Join status 37
- Communicator 38
- Field Communicator 39
- AMS creating a Reusable Copy 40
- Section 3 Installation 41
- 3.2.1 Warnings ( ) 42
- 3.3 Considerations 43
- Internal antenna position 44
- Steam service 44
- Side mounted 44
- Installation 45
- Reducing process noise 46
- Output damping 46
- Reference side filtering 46
- 3.4 Installation procedures 47
- 3.4.1 Mount the transmitter 48
- Flange bolts 49
- Bolt installation 50
- Section 3: Installation 52
- 3.4.2 Impulse piping 53
- Mounting Requirements 54
- 3.4.3 Process connections 55
- Sensor Module 57
- Process Connection 57
- 3.5.4 Manifold operation 62
- Section 4 Commissioning 67
- 4.2.1 Warnings ( ) 68
- 4.3 Viewing network status 69
- 4.4 Verifying operation 69
- Smart Wireless Gateway 70
- Troubleshooting 71
- Join Device to 72
- Network 72
- HART lock 73
- 2, 2, 7, 4 74
- 2, 2, 7, 2 74
- 5.1 Overview 75
- 5.2 Safety messages 75
- 5.3 Calibration overview 75
- Digital Zero 77
- Sample calculation for 2051 78
- 5.4 Trim the pressure signal 79
- 5.4.2 Sensor Trim 80
- Zero Effect 82
- Span Effect 82
- Zero Effect: 83
- Span Effect: 83
- LT = LRV + S x (LRV) x P 83
- HT = URV + S x (URV) x P 83
- 5 8. 0 85
- 2 5. 2 5 86
- A b c d e 87
- 87
- N E T w K 89
- S R C H N G 89
- P R E S S 91
- P S I 91
- S u p l y 92
- 3. 6 0 92
- f a i l u r 93
- w a r n 94
- Section 6 Troubleshooting 95
- 6.2.1 Warnings ( ) 96
- 6.3 Removing from service 100
- Reference Accuracy 102
- Total Performance 102
- Long Term Stability 103
- Dynamic Performance 103
- A.2 Functional Specifications 104
- A.2.2 Range and Sensor Limits 105
- A.3.1 Overpressure limits 106
- A.3.2 Static pressure limit 107
- A.3.3 Burst pressure limits 107
- A.3.4 Temperature limits 107
- A.3.5 Humidity Limits 108
- A.3.6 Volumetric Displacement 108
- A.3.7 Damping 108
- A.4 Physical specifications 109
- A.4.5 Non-Wetted Parts 110
- Sensor Module Fill Fluid 111
- Cover O-rings 111
- Power module 111
- 00809-0100-4102, Rev AA 112
- May 2013 112
- A.5 Dimensional Drawings 113
- A.6 Ordering Information 115
- 2–14 NPT Female ★ 120
- Standard Standard 122
- 2-in. NPT) ★ 129
- Appendix A: Reference Data 138
- A.7 Options 139
- Output information 140
- Display and interface options 140
- Configuration buttons 140
- A.8 Spare parts 142
- B.1 Wireless Certifications 143
- B.1.8 European certifications 144
- Product Certifications 146
- Trees and Fast Keys 147
- D.1 Effective range 151
Manuais e produtos relacionados com Medição, teste e controlo Emerson Rosemount 2051 Wireless Pressure Transmitters
(3 páginas)
Medição, teste e controlo Emerson 3051S Especificações
(188 páginas)
(188 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais