Emerson 3051S Especificações Página 77
- Página / 188
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
51
Reference Manual
00809-0100-4803, Rev DA
Section 3: Configuration
April 2013
Configuration
To calculate the Base per Custom value for a custom unit not shown in Tab le 3 -10 , see one of
the following examples:
Energy Conversion Example: page 51
Time Conversion Example: page 52
Energy and Time Conversion Example: page 52
Energy conversion example:
To find the Base per Custom relationship for a custom unit of thousands of BTU per hour (kBtuh)
and a base unit of BTU per hour (Btu/h), input the following:
Custom Unit = kBtuh
Base Unit = Btu/h
Because:
1 kBtu (Thousands of BTU) = 1000 Btu
Then:
1 kBtuh = x = 1000 Btu/h
1 kBtuh = 1000 Btu/h
Therefore:
Base per Custom = = = 1000
1kBtu
1h
---------------------
1000 Btu
1h
---------------------------
Number of Base Units
1xCustomxUnit
-----------------------------------------------------------------------
1000 Btu h
1kBtuh
-----------------------------------
- Rosemount 3051S MultiVariable 1
- Transmitter 1
- Contents 5
- Table of Contents 6
- 5Section 5: Troubleshooting 7
- Section 1 Introduction 9
- 1.2 Models covered 10
- 1.3 Service support 10
- Section 2 Installation 11
- 2.2.1 Warnings 12
- 2.4 Installation procedures 13
- 2.4.2 Mounting considerations 14
- LCD display rotation 15
- Feature board side of housing 15
- Cover installation 15
- Conduit entry threads 15
- Cover jam screw 16
- Process flange orientation 16
- 2.4.3 Mount the transmitter 17
- Flange bolts 18
- Mounting requirements 19
- 2.4.4 Process connections 20
- ROSEMOUNT 3051S / 3051 / 2051 21
- Impulse piping considerations 22
- Surges/transients 25
- Signal wire grounding 26
- 2.4.7 Grounding 27
- 305 INTEGRAL 29
- COPLANAR 29
- 305 INTEGRAL TRADITIONAL 29
- 304 TRADITIONAL 29
- 304 WAFER 29
- Section 2: Installation 34
- Installation 34
- Section 3 Configuration 35
- 3.2 Safety messages 36
- Connecting to a PC 38
- 3.4 Flow configuration 39
- Online and offline mode 40
- 3.4.4 Preferences 42
- 3.4.6 Fluid properties 46
- 3.4.8 Save / send 49
- Saving a configuration 51
- Sending a saved configuration 51
- Natural gas 52
- Custom gas 54
- Custom liquid [Density (T)] 55
- Units of measure 57
- 3.6.1 Model identification 60
- 3.6.2 Alarm and saturation 60
- 3.6.3 Variable mapping 62
- 3.6.4 LCD display 63
- 3.6.5 Communication setup 64
- Burst mode 65
- Enabling burst mode 65
- Choosing a burst option 66
- Multidrop communication 66
- Loop current mode 67
- 3.7 Variable configuration 69
- Time conversion example: 73
- 3.7.2 Energy rate 75
- Energy conversion example: 77
- Section 3: Configuration 79
- Configuration 79
- 3.7.3 Totalizer 81
- Totalizer conversion example: 83
- 3.7.4 Differential pressure 84
- 3.7.5 Static pressure 85
- 3.7.6 Process temperature 86
- 3.7.7 Module temperature 87
- 3.7.8 Analog output 88
- (page 1) 91
- (page 2) 92
- 3.8.5 475 Fast keys 95
- Function Fast Key Sequence 96
- 4.1 Overview 99
- 4.2 Safety messages 100
- 4.3 Transmitter calibration 101
- 4.3.2 Sensor trim overview 102
- Zero trim 103
- Upper and lower sensor trim 103
- Calibration type 104
- Recall factory trim 104
- Last DP sensor trim point 104
- 4.3.6 Analog calibration 108
- Analog output loop test 109
- 00809-0100-4803, Rev DA 110
- April 2013 110
- 4.5 Process variables 111
- 4.5.2 All variables tab 112
- Field device labels 113
- Remove the feature board 114
- Black Rubber V-Seal 115
- 4.6.3 Terminal block 116
- 4.6.4 LCD display 117
- 4.6.5 Flange and drain vent 117
- 4.6.6 SuperModule assembly 119
- Reference Manual 120
- Operation and Maintenance 120
- Section 5 Troubleshooting 121
- Section 5: Troubleshooting 122
- Troubleshooting 122
- Symptom Corrective Actions 124
- Symptom Corrective Action 128
- Reference Data 131
- Total performance 132
- Long term stability 133
- Warranty 133
- Ambient Temperature effect 134
- Line Pressure effect 135
- Mounting Position Effects 135
- Vibration effect 135
- Power supply effect 136
- Range and sensor limits 137
- 4–20 mA/HART 138
- Overpressure limits 139
- Static Pressure limit 139
- Burst Pressure limits 140
- Temperature limits 140
- Humidity limits 140
- Volumetric displacement 141
- Failure mode alarm 141
- A.1.3 Physical specifications 142
- Sensor module fill fluid 143
- Cover O-rings 143
- A.2 Dimensional drawings 145
- Pipe Mount Panel Mount 146
- Appendix A: Reference Data 147
- 3.56 Max open 148
- (90 Max open) 148
- A.3 Ordering information 149
- 2-14 NPT flange adapter ★ 152
- 2 SST flange adapter 152
- A.4 Accessories 157
- A.5 Exploded view diagram 158
- A.6 Spare Parts 159
- North American certifications 166
- European certifications 166
- Japanese certifications 167
- INMETRO certifications 168
- China (NEPSI) certifications 168
- IECEx certifications 169
- B.5 Installation drawings 171
- Product Certifications 172
- B.5.3 GE / GM option NEMA 4X 181
Manuais e produtos relacionados com Medição, teste e controlo Emerson 3051S
Medição, teste e controlo Emerson 3051S Especificações
(240 páginas)
(240 páginas)
Medição, teste e controlo Emerson 3051S Especificações
(240 páginas)
(240 páginas)
Medição, teste e controlo Emerson 644 Especificações
(182 páginas)
(182 páginas)
Medição, teste e controlo Emerson 3051S Especificações
(222 páginas)
(222 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais