Emerson MICRO MOTION 2700 Manual de Instalação Página 129
- Página / 264
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Transmitter Configuration and Use: Series 1000 and 2000 Transmitters 119
Troubleshooting continued
Troubleshooting DiagramsDefaultsCompensation
A14 Electronics failure Transmitter Fail Cycle power to the flowmeter.
The transmitter might need service. Contact Micro
Motion. See Section 10.3.
A15 Data Loss Possible Data Loss Possible Cycle power to the flowmeter.
Perform sensor coil and resistance tests. See
Section 10.26.
The transmitter might need service. Contact Micro
Motion. See Section 10.3.
A16 Line RTD Overrange Line Temp Out-of-range Check the test points. See Section 10.24.
Check the sensor coils. See Section 10.26.
Check wiring to sensor. See Section 10.13.2.
Make sure the appropriate sensor type is
configured. See Section 6.2.
Contact Micro Motion. See Section 10.3.
A17 Meter RTD Overrange Meter Temp
Out-of-Range
Check the test points. See Section 10.24.
Check the sensor coils. See Section 10.26.
Contact Micro Motion. See Section 10.3.
A18 EEPROM Checksum—
1000/2000
EEPROM Checksum Cycle power to the flowmeter.
The transmitter might need service. Contact Micro
Motion. See Section 10.3.
A19 RAM Error—
1000/2000
RAM Error Cycle power to the flowmeter.
The transmitter might need service. Contact Micro
Motion. See Section 10.3.
A20 Calibration Factor
Unentered (Flocal)
Cal Factor Unentered Check the characterization. Specifically, verify the
FCF value. See Section 6.2.
A21 Unrecognized/
Unentered Sensor Type
(K1)
Incorrect Sensor Type Check the characterization. Specifically, verify the
K1 value. See Section 6.2.
A22 EEPROM Config
Corrupt–Core Processor
Configuration Corrupt Cycle power to the flowmeter.
The transmitter might need service. Contact Micro
Motion. See Section 10.3.
A23 EEPROM Totals
Corrupt–Core Processor
Totals Corrupt Cycle power to the flowmeter.
The transmitter might need service. Contact Micro
Motion. See Section 10.3.
A24 EEPROM Program
Corrupt–Core Processor
CP Program Corrupt Cycle power to the flowmeter.
The transmitter might need service. Contact Micro
Motion. See Section 10.3.
A25 Core Processor Boot
Sector Fault
Boot Sector Fault Cycle power to the flowmeter.
The transmitter might need service. Contact Micro
Motion. See Section 10.3.
Table 10-5 Status alarms and remedies (continued)
Alarm
code Communicator ProLink II software Possible remedy
- Micro Motion 1
- Series 1000 and 1
- Series 2000 Transmitters 1
- Contents 5
- Chapter 1 11
- Before You Begin 11
- Before You Begin continued 13
- Topic Document 13
- Term Definition 13
- Item Configuration data 15
- Chapter 2 17
- Using the Transmitter Display 17
- –8.100E 5 19
- Chapter 3 21
- Poll button in the Connect 26
- 1 and 2, or to the 26
- Connect to Device 32
- Chapter 4 33
- 375 Field Communicator 33
- Chapter 5 39
- Flowmeter Startup 39
- Flowmeter Startup continued 40
- 5.5.3 Zeroing with ProLink II 50
- Chapter 6 53
- Sensor type 54
- T- S er ie s O t he r 54
- Newer tag Older tag 55
- Flow FCF X.XXXX FT X.XX 56
- Terminals 58
- Default Process 58
- Mass flow unit 60
- Volume flow unit 61
- ProLink II code 69
- Communicator 69
- Polarity 75
- Output power 75
- Description 75
- Assignment ProLink II code 77
- Using the Transmitter 79
- Chapter 7 79
- • Model 1700 AN 84
- • Model 1700 IS 84
- • Model 2700 AN 84
- • Model 2700 IS 84
- • Model 2700 CIO 84
- Scroll optical switch 85
- Select optical switch 85
- Function name Communicator 86
- ProLink II 86
- ProLink 87
- Totalizer Control 87
- With a Communicator 88
- Chapter 8 89
- Optional Configuration 89
- Table 8-1 Configuration map 90
- Special 92
- • Model 2500 CIO 93
- Variable Description 94
- Cutoff type Default Comments 96
- Example 1 100
- Example 2 100
- Example 3 101
- Informational panel of the 102
- Status window 102
- Scroll to view process 104
- Max Int. Totalizers stop 106
- Parameter 109
- Series 1000 Series 2000 110
- Process variable 110
- PV SV TV QV PV SV TV QV 110
- Parameter Description 111
- Chapter 9 113
- Compensation, and Polling 113
- Pressure unit 114
- Static pressure 116
- Polled Var 1 119
- Chapter 10 121
- Troubleshooting 121
- Troubleshooting continued 122
- Section Topic 122
- Symptom Cause Possible remedy 132
- Pickoff value 141
- Cause Possible remedy 141
- Test terminal pair 146
- Colors Numbers 146
- Possible cause Solution 147
- Appendix A 151
- Default Values and Ranges 151
- Appendix B 155
- Appendix C 167
- Calibrating the Transmitter 167
- Appendix D 175
- Name Description 176
- Available process variables 178
- Slope and offset 181
- Appendix E 183
- Other configuration options 185
- Preferences menu 187
- Figure E-4 Communicator menus 188
- Appendix F 193
- Figure F-4 Communicator menus 197
- Appendix G 203
- Transmitters 203
- Figure G-4 Communicator menus 207
- Enter password if required 212
- Appendix H 219
- Figure H-4 Communicator menus 223
- Appendix I 235
- Configuration 237
- Figure I-4 Communicator menus 239
- On-Line Menu 240
- 3 Basic Setup 240
- 4 Detailed Setup 240
- 5 Review 243
- Appendix J 251
- Select to disable 252
- Select to enable 252
- Index continued 256
- *20001715* 264
Manuais e produtos relacionados com Medição, teste e controlo Emerson MICRO MOTION 2700
(3 páginas)
Medição, teste e controlo Emerson 3051S Especificações
(188 páginas)
(188 páginas)
Medição, teste e controlo Emerson 3051S Especificações
(240 páginas)
(240 páginas)
Medição, teste e controlo Emerson 3051S Especificações
(240 páginas)
(240 páginas)
Medição, teste e controlo Emerson 644 Especificações
(182 páginas)
(182 páginas)
Medição, teste e controlo Emerson 3051S Especificações
(222 páginas)
(222 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais