Emerson Autochangeover Controllers AC8 Manual do Utilizador descarregar pdf (Página 2)

Revision B.33 2/25/2011

Liebert Monitoring Group – Development

Page 2 of 149

Revision Level Updates:

Revision

Date

Description

B.5

11/8/00

Added: revision level update chart, HiPulse support, and NPower support

B.6

2/19/01

Revised NPower definition

B.7

4/4/02

Added support for HiMod LNA

B.8

5/3/02

Revised Modbus explanation (Hi Byte / Lo Byte)

B.9

10/1/02

Corrected NPower table (typing error)

B.10

1/22/03

Added support for DataMate

B.11

7/23/03

Added support for STS-2

B.12

4/19/04

Corrected ModBus register addressing for STS-2 alarms. PM2 – removed duplicate

Output Voltage THD Alarm. Added XDP Unit. Added LDS5000 Unit. Added Universal

Monitor. Added BACNet/IP for: WDU, MM4, SC4, PM2 & LAM. Added Run Hours for

MM2

B.13

5/24/04

Removed non-existent alarms for MM2. Added BacNet/IP Point addresses for MM2.

B.14

8/19/200

Track issue 3576 – Make BacNet points consistent with Modbus Points.

B.15

11/22/20

Added ESP-2 based UPS Units that use OC485 card. Includes Nx, HiNet, PSI, and

GXT

B.16

5/18/05

Added “High Water Humidifier Pan” alarm to L00. Corrected alarm points for BACNet

and Modbus addressing on STS-2.

B.17

7/1/05

Added Remote shutdown alarm to LAM. Added Note about Alarms “BACNet auto

discovery” to CCM, L00, LAM, MMS, PM2, PMP, SCC. Added note to STS2 that it is

for units with or without PDU. Changed breaker status register for STS2 from bits1-8

to 0-7.

B.18

7/21/05

Added XDC Unit. Added control point note for units with on/off control as follows: Bit

0 on=unit off Bit 1 on=unit on. Removed cables 3 & 4 on LDS5000 and marked these

registers as spares.

B.19

11/30/05

Corrected revision level and date in header on this document.

B.20

12/14/05

SMS – Added Scale factor for kVA & kW. Revised note on page 1 to state module

type rather than “SS2000 Hardware”.

B.21

8/9/06

Series 610 UPS – added note that Series 610 is the same as series 600. SC4-SM4

changed “Bypass Breaker Closed” alarm from “Bypass Breaker Open”. Added note to

LAM that iCOM w/native IGM also applies.

B.22

8/10/06

Nfinity UPS (pnf), Nx (pnx), STS-2 (st2) – deleted status and setpoint points that are

not displayed in SiteScan. XDC, XDP added scale factor notes for Ref, Fluid and CW

temps.

B.23

3/16/07

PMP – Local Alarm #1 was Load Alarm, Added Local Alarm #2, Corrected Modbus

addressing from 40290:04 to 40290:07

B.24

4/16/07

AC8 – Added Unit tables to reference library

B.25

4/30/07

MM2 – Corrected entire table due to MS Word problems.

B.26

5/2/07

Corrected major MS Word formatting problems throughout document.

B.27

11/15/07

Added iCOM DS unit for 2mb modules (small version), SM3 corrected reversed

Modbus addressing for kW & kVA. Noted that pages for Series 600 UPS also apply

to series 610.

B.28

6/24/08

Added iCOM-XDP unit

B.29

7/11/08

Corrected alarm info for Npower (IMP) unit.

B.30

5/13/09

Corrected revision number in page header B.30 from B.9. Changed XDP unit

description on page 53 from XD. Corrected miscellaneous document formatting

errors. Added WDU definition back in document from accifental deletion.

B.31

10/13/09

Added local Alarms 2,3 &4 for MM2, L00 & LSM. Local alrm 3=High Water for MM2

B.32

4/23/10

Clarified LAM/iCOM program usage and added iCOM 16mb version. Added

examples and notes sections. Removed discontinued modules.

B.33

2/2/11

Removed General Alarm from iCOM_DS. Added Hi Water Humidifier Pan to L8T.

Moved Generator Disconnected from Alarm to Status in NX unit.

1 2 3 4 5 6 7 ... 148 149

Comentários a estes Manuais

Sem comentários

Emerson Autochangeover Controllers AC8 Manual do Utilizador Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Comutadores de rede Emerson Autochangeover Controllers AC8